Skip to content
HVAC · Cash and pricing

HVAC flat rate pricing: the math behind the book

By Mike Ventrella7 min read

A cut-paper illustration seen from above of an open price binder on a wood table, with a capacitor, a fan motor, a gauge set and a tablet showing three option cards.

HVAC flat rate pricing gives the customer one price per task before the work starts, whatever the clock says. Every line in the book comes from the same formula: book time × your cost per billable hour, plus parts at cost, divided by one minus your target gross margin. At $56 a billable hour and a 45% margin, a capacitor swap with 0.75 hours of book time and $25 in parts sells for $122.

The formula is the easy part. Flat rate books lose money in three places: a member discount nobody priced in, book times your techs don't hit, and a bought book built on someone else's labor rate. This guide shows the math on each, with example numbers for a residential service shop. If you run an HVAC company, your P&L and timesheets already hold every input.

What goes into HVAC flat rate pricing?

Three inputs, and you set all of them:

  • Book time: the hours a good tech takes to do the task, start to finish, at the house.
  • Cost per billable hour: what a tech costs you for each hour you can invoice, with payroll taxes, workers' comp, benefits and the unbilled hours (drive time, shop time, callbacks) loaded in.
  • Target gross margin: your overhead as a share of revenue plus the net profit you want. Gross margin is what's left of the price after labor and parts.

The cost per billable hour is where most books go wrong. The median HVAC tech earned $29.33 an hour in May 2025, according to the Bureau of Labor Statistics. Load that with burden and the hours nobody bills, and our HVAC pricing guide lands near $56 per billable hour. Run your own with the labor burden calculation; it's the number that moves every line in the book.

A flat rate book, line by line

Here's a starter page for an example shop at $56 a billable hour and a 45% target margin. The book times and parts costs are examples; use your own supply house invoices.

Task Book time Labor Parts at cost Job cost Flat rate (÷ 0.55)
Run capacitor 0.75 hr $42 $25 $67 $122
Contactor 0.75 hr $42 $30 $72 $131
Clear condensate drain 1 hr $56 $5 $61 $111
Furnace igniter 1 hr $56 $45 $101 $184
Condenser fan motor and capacitor 1.5 hr $84 $180 $264 $480

Divide by 0.55. Don't multiply by 1.45. A 45% markup on that $264 fan motor job gives $383, which is a 31% margin and $97 short on one call. The HVAC pricing guide walks through that mistake in detail.

Keep the book short. We did a ride-along with an electrical contractor whose salespeople had never been electricians, and some had sold cars. They were still selling $40,000 packages, because the owner had cut the price book from 4,000 items down to 200. Fewer, clearer lines are what let anyone on the crew quote the same job the same way.

What does a member discount cost you?

More than the discount. If your maintenance agreement gives members 15% off the book, a line priced at a 45% margin drops to about a 35% margin for members:

Fan motor and capacitor Non-member Member (15% off)
Price $480 $408
Job cost $264 $264
Gross profit $216 $144
Gross margin 45% 35%

If half your repair calls go to members, your average repair margin is closer to 40% than 45%, and the overhead you priced for doesn't get paid.

The fix is to build the discount into the book. Price each line so the member price hits your target: job cost ÷ 0.55 ÷ 0.85. For the fan motor job, that's $565 for non-members and $480 for members. The member still sees a real 15% off, and the agreement stops eating your margin. If you'd rather keep the lower prices, that's a fair choice, but count the agreement fees as the margin you're buying back and check that they cover it.

Do your techs hit the book times?

Flat rate moves the risk of a slow job from the customer to you. If the book says 1.5 hours and the tech averages 2.25, that $480 job really costs $306 (2.25 × $56 + $180), and the margin falls from 45% to 36%.

Check it once a month:

  1. Pull every flat rate invoice for the month from your field software, with the task and the book hours on each.
  2. Pull the clocked hours for the same jobs from your timesheets.
  3. For each of your 10 busiest tasks, divide the clocked hours by the book hours.
  4. Anything above 1.15 for two months running gets a new book time or a training ride-along, depending on whether the book or the tech is off.

Job costing gives you the actual margin on each job, which is the same check from the money side.

The same report tells you how to pay. If you pay techs per flat rate task, you've handed them the speed incentive too.

performance based pay flat Commission can lead to quality control issues where they just want to rush to get done … there's ways that you can mitigate that you can have different tiers of bonuses if they get five-star reviews if they don't have fix-its or callbacks.

That's what we told an owner who was weighing a switch to pure commission for his techs. Tie part of the pay to callbacks and reviews, and the book time stops being a race.

Should you buy a flat rate book?

A bought book saves you writing hundreds of task descriptions and book times. It doesn't know your costs. Every bought book is built on some hourly rate and parts markup, and if those came from a shop with different wages or a different overhead, every price on the page carries the error.

Test it before you load it. Take 5 lines you sell every week and, for each one, work out the margin the book's price gives you:

Margin = 1 − (book time × your cost per billable hour + parts at cost) ÷ book price

Using the example cost above, a bought book that lists the capacitor swap at $105 gives you 1 − ($42 + $25) ÷ $105, about 36%. If your target is 45%, raise the book's labor rate or parts multiplier until those 5 lines hit it, then spot-check 5 more.

ACCA's Contractor of the Future study of more than 1,000 HVACR contractors found that those using flat rate on service calls reported average net profits of 7%, against 4% for other methods. That edge only shows up when the book's math matches your P&L.

Questions owners ask

Can I give a discount off the flat rate price?

Not one the book didn't plan for. Flat rate works because every customer gets the same price for the same task.

don't jump in jack up the price so that you can negotiate down. … I just like to give one price. That's our final price and that's the only thing that we offer.

That's one owner we know, asked how he answers "is this the best you can do?", passing on a rule his dad taught him.

Planned discounts, like the member price, go in the book. Everything else stays off the table.

How do good, better and best options fit?

Each option is its own line, priced with the same formula. A "best" option that adds a hard start kit and a surge protector to the capacitor swap gets its own book time and parts cost, then the same ÷ 0.55. Don't price the upgrades as a percentage on top of the basic line.

How often should I update the book?

Every January, when payroll taxes and unemployment rates reset, after raises, and whenever the supply house moves prices. Because each line comes from the same three inputs, one change to cost per billable hour reprices the whole book. Compare your result with the HVAC profit margins benchmark to see whether the margin target itself needs to move.

Keep the margin you priced on every flat rate call

Work out your own cost per billable hour first, then run 5 lines you sell every week through the margin test. That one number moves every price in the book, so getting it right is what keeps the margin you priced on every call. If you're not sure your P&L shows a true overhead number to set that margin from, bring last month's to a free profit call and we'll look at what your numbers are telling you about your book.

Keep reading

See every article
  • Plumbing pricing: how to price plumbing jobs

    Plumbing pricing starts with what one billable hour of a plumber and a truck costs you. Here's the math, flat rate vs T&M, trip fees and after-hours rates.

  • How to price electrical work

    Price electrical work from one billable-hour rate: labor, overhead and profit per hour you invoice. Here's the math on a panel upgrade and an EV charger.

  • Plumbing business profit margins by job type

    No public benchmark covers plumbing shops your size. Here's what Roto-Rooter's filing shows, a worked P&L by job type and how to find which work pays.

Know what to change next month.

It starts with a free 30-minute call, and you'll leave knowing what your books need and what it costs.

100% money-back in your first 30 days.